Home > EIGRP OSPF Redistribution Sim

EIGRP OSPF Redistribution Sim

January 8th, 2015 in Lab Sim, LabSim Go to comments

Question

OSPF_EIGRP_Redistribution.jpg

Answer and Explanation:

First we need to find out 5 parameters (Bandwidth, Delay, Reliability, Load, MTU) of the s0/0/0 interface (the interface of R2 connected to R4) for redistribution :

R2#show interface s0/0/0

Write down these 5 parameters, notice that we have to divide the Delay by 10 because the metric unit is in tens of microsecond. For example, we get Bandwidth=1544 Kbit, Delay=20000 us, Reliability=255, Load=1, MTU=1500 bytes then we would redistribute as follows:

R2#config terminal
R2(config)# router ospf 1
R2(config-router)#
redistribute eigrp 100 metric-type 1 subnets
R2(config-router)#exit
R2(config-router)#router eigrp 100
R2(config-router)#redistribute ospf 1 metric 1544 2000 255 1 1500

(Notice: In fact, these parameters are just used for reference and we can use other parameters with no problem. Also, a candidate said that the simulator didn’t accept the Bandwidth of 1544; in that case, we can use a lower value, like 128.

If the delay is 20000us then we need to divide it by 10, that is 20000 / 10 = 2000)

Note: “usec” here does not mean microsecond (which is 1/1000 milliseconds) but means millisecond. In short usec = msec. I don’t know why they use the word “usec” here but just think it is “msec” (According to this link: http://www.cisco.com/en/US/tech/tk365/technologies_white_paper09186a0080094cb7.shtml#eigrpmetrics: “The delay as shown in the show ip eigrp topology or show interface commands is in microseconds”)

For R3 we use the show interface fa0/0 to get 5 parameters too

R3#show interface fa0/0

For example we get Bandwidth=10000 Kbit, Delay=1000 us, Reliability=255, Load=1, MTU=1500 bytes

R3#config terminal
R3(config)#
router ospf 1
R3(config-router)#
redistribute eigrp 100 metric-type 1 subnets
R3(config)#
exit
R3(config-router)#
router eigrp 100
R3(config-router)#
redistribute ospf 1 metric 10000 100 255 1 1500

Finally you should try to “show ip route” to see the 172.16.100.1 network (the network behind R4) in the routing table of R1 and make a ping from R1 to this network.

Note: If the link between R2 and R3 is FastEthernet link, we must put the command below under EIGRP process to make traffic from R1 to go through R3 (R1 -> R2 -> R3 -> R4), which is better than R1 -> R2 -> R4.

R2(config-router)# distance eigrp 90 105

This command sets the Administrative Distance of all EIGRP internal routes to 90 and all EIGRP external routes to 105, which is smaller than the Administrative Distance of OSPF (110) -> the link between R2 & R3 will be preferred to the serial link between R2 & R4.

A reader on our site has a closer explanation for the “distance eigrp 90 105” command so we quote it here for your reference:

The “distance” refers to the administrative distance of the routes provided by a given routing process. By default, internal (which means non-redistributed) EIGRP routes are given an administrative distance of 90 while external (redistributed from another routing process) EIGRP routes are given an administrative distance of 170. The default administrative distance of OSPF is 110. The administrative distance measures the “distance from the truth” and tells the router which routes are more trustworthy. Lower administrative distance = more trustworthy. For this reason, connected routes have an administrative distance of 0. They are the MOST TRUSTWORTHY, because they are physically connected to the router. When making a decision about which route to install in the routing table, the router looks at administrative distance first. The metric (or cost) is only considered if two routes have the same administrative distance.

In this case, R2 will learn about R4’s loopback network from both R4 and R3. The route from R4 will be in OSPF (admin distance of 110) because R2 is also running OSPF while the route from R3 will be an external EIGRP route (administrative distance of 170 by default). Since the OSPF route has a lower administrative distance, it will get placed in R2’s routing table and the R3-provided route will be ignored. This is not optimal, since the path through R3 is a faster, more reliable path. To fix this, we change the administrative distance of external EIGRP routes at R2 by using the “distance eigrp 90 105” command. This sets the administrative distance of internal EIGRP routes to the default of 90 and changes the administrative distance of external EIGRP routes to 105 (less than that of OSPF routes). Now, when R2 learns of the loopback network from R4 and R3, it will install the now lower administrative distance external EIGRP route from R3 and our traffic from R1 will take the faster path.

Note: Please check the OSPF process numbers first before typing these commands.

If you want to have a closer look at this sim and understand more about the “distance eigrp” command, please read my OSPF EIGRP Redistribute Lab in GNS3.

Other lab-sims on this site:

EIGRP Stub Sim

OSPF Sim

IPv6 OSPF Virtual Link Sim

EIGRP Simlet

Policy Based Routing Sim

Comments
Comment pages
1 2 26
  1. CoolGuy
    January 9th, 2017

    Hi NK2

    Congratss for your cisco route exam.

    I am taking the exam on 11th Jan..

    If I could get the stuff on ictpro08 at hotmail dot com that would be much appreciated…

    Thanks in advance.

  2. Drago
    January 9th, 2017

    i downloaded the lab from tut and ran in my gns3. It looks like the answer does not correspond to the lab because IEGRP is already redistributed into OSPF. We need to do redistribution the other way. From OSPF into EIGRP. Anyone noticed that the answer is wrong ?
    I might miss the explanation in the thread but really don’t want to read 30 pages of posts.

    Can you guys check the lab?

  3. AFI
    January 9th, 2017

    @ ADMIN – whoever that is.
    I dont think OSPF EIGRP redistribution lab is complete. i think there needs to be a default route in R1 for it to ping R4 loopback address.

    @drango,
    i just ran files, i had to redistribute in R2 & R3. only issue I found is mentioned above.

  4. malik
    January 10th, 2017

    In this Redistribution lab, There is no need to use match and set tag values for redistribution EIGRP to OSPF and OSPF to EIGRP?

  5. Konan
    January 10th, 2017

    Again question,what is the purpose setting metric type to 1?

  6. mirzo94
    January 11th, 2017

    Hi dear @NK2, please can you also send to me, ahilles05.94 at gmail dot com. Thank you before hand

  7. CoolGuy
    January 11th, 2017

    Cleared Exam Today … !!!!
    149Q +Tagwa 41 Qs are still valid.
    Got the followng Labs+Sim in exam
    OSPF Evaluation
    EIGRP OSPF Redistribution
    Policy Based Routing
    OSPFv3 Virtual Link
    Thanks DigitalTut and all those who shares their knowledge and useful stuff.
    — Best Of Luck —

  8. Coolguy
    January 11th, 2017

    hi NK2
    I have schedule my exam on 20th of january

    please send me engsk27atgmail.com

  9. Anonymous
    January 11th, 2017

    hi, nk2 kindly send me the dumps
    {email not allowed}

  10. prisca
    January 11th, 2017

    hi, nk2 kindly send me the dumps
    priscakashatgmail.com

  11. ahemd erlrofaie
    January 13th, 2017

    can any one send me 149+41 and 183 dumps
    i will be so grateful my email address is
    ahmedrofai at gmail dot com

  12. ahemd erlrofaie
    January 13th, 2017

    is pass4sure 150 dump is valid

  13. Thankfulguy
    January 15th, 2017

    149Q +Tagwa 41 Qs PLEASE HELP taking the exam on the 21st THANK YOU southern.kick16 @ gmail.com

  14. NK2
    January 16th, 2017

    I have sent the dumps to most of the people and i advise you to help each other. If some one is missing, they can send me a request on naveedkhalid25 at gmail dot com.

  15. ahemd erlrofaie
    January 17th, 2017

    Refer to the following configuration command.
    router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
    Which statement about the command is true?

    A. Any packet that is received in the inside interface with a source IP port address of
    172.16.10.8:80 is translated to 172.16.10.8:8080.
    B. Any packet that is received in the inside interface with a source IP port address of
    172.16.10.8:8080 is translated to 172.16.10.8:80.
    C. The router accepts only a TCP connection from port 8080 and port 80 on IP address
    172.16.10.8.
    D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8
    is redirected to port 8080 or port 80.

    here in tagwa dump it say the correct answer is a but i think it b , can any one advice

  16. Malak
    January 17th, 2017

    I think this command parameters is not correct:
    R3(config-router)#redistribute ospf 1 metric 10000 100 255 1 1500

    because fast ethernet BW is 100,000 and its bandwidth is 100 witch become 10 after divided it by 10
    on other-hand I don’t think its right to change AD of EIGRP where this case a loop issue
    the rule is to make sure that AD of internal Routing AD of external EIGRP (105)

  17. Malak
    January 17th, 2017

    the rule is to make sure that AD of internal Routing less than external Routing…
    AD of internal OSPF (110) bigger than AD of external EIGRP (105), this may cause a loop

  18. malik
    January 17th, 2017

    I pass my exam today with 947 marks. 149 + 41 are 100% valid. All questions from these two dumps nothing else.
    OSPF V3
    OSPF Evaluation
    Redistribution
    PBR
    OSPF V2

    CHAP Drag and Drop

  19. freeman
    January 18th, 2017

    Can someone please send me TAGWA on dr.freeman91 at gmail . com

  20. CoolGuy
    January 20th, 2017

    Hi Guys,

    From following link CCNP Labs +149Q +Tagwa 41 Qs can be downloaded.

    Note: Remove (total 8)”$” from the link to work

    ht$$tps:$$//1drv.ms/f/$$s!Aq7EzlPsYq2YgSN-WUs6kzGVn2V9K$$

  21. CoolGuy
    January 24th, 2017

    Hi Guys,
    From following link CCNP Labs +149Q +Tagwa 41 Qs can be downloaded.
    Note: Remove (total 8)”$” from the link to work
    ht$$tps:$$//1drv.ms/f/$$s!Aq7EzlPsYq2YgSN-WUs6kzGVn2V9$$

  22. ahemd erlrofaie
    January 24th, 2017

    Hi guys, I have passed my ccnp routing exam yesterday at (23/1/2017) with score (973), actually the dumps of 149q and 41q tagwa is still valid.
    Most the question came from the 41q tagwa, so you have to study it very well,
    BUT it important to study also the dump of 183q/32q/8q because it contain a lot of questions that you will not find them in both 149q and tagwa 41q dumps, in my exam none of new questions of 183q/32q/8q came, but I recommended to studied any way
    The sim in my exam:
    -ospf eigrp redistribution
    -ospf evaluation
    -ospfv3 with virtual-link
    -ospf sim
    The drag and drop:
    -CHAP drag (in tagwa 41q)

    Important notes about the sims:
    Regarding to sims , you should be careful because you might find that there some minor changes in the sims (like ip addess, subnets , ospf process numbers , eigrp autonomous number and so on) so check with show run command if that possible, before starting the configuration to not rush to configure blindly .
    In my exam, there was some little change in ospf evaluation, I mentioning below the question with changed answer:
    The question:
    Which of the following statements is true about the serial links that terminate in R3?
    A. The R1-R3 link needs the neighbor command for the adjacency to stay up
    B. The R2-R3 link OSPF timer values are 30, 120, 120
    C. The R1-R3 link OSPF timer values should be 10,40,40
    D. R3 is responsible for flooding LSUs to all the routers on the network.
    In dumps sim you will find that the correct answer is B, but in my exam that was not true, because I found that the exam changed the link R2-R3 timers to 10,40,40 and it was point-to-point link.
    also I found The link R1-R3 timer was 30,120,120 non-broad cast link, so both of the answers A , B are wrong .
    Also D was wrong because, R3 was not the DR in all the links,
    The right answer was A, because the link R1-R3 is non-broad-cast link so neighborship should be configured manually.
    So it is important to be carful .

    Important notes about tagwa 41q dump:
    It is important to mention that in tagwa 41q dump there some questions with wrong answers, here below I mentioned the question with the wrong answers:
    Question 2
    Refer to the following configuration command.
    router(config)# ip nat inside source static tcp 172.16.10.8 8080 172.16.10.8 80
    Which statement about the command is true?
    A. Any packet that is received in the inside interface with a source IP port address of
    172.16.10.8:80 is translated to 172.16.10.8:8080.
    B. Any packet that is received in the inside interface with a source IP port address of
    172.16.10.8:8080 is translated to 172.16.10.8:80.
    C. The router accepts only a TCP connection from port 8080 and port 80 on IP address
    172.16.10.8.
    D. Any packet that is received in the inside interface with a source IP address of 172.16.10.8
    is redirected to port 8080 or port 80.
    Answer:A
    Tagawa say the right answer is A , but that wrong the right answer is B (this question came in my exam)

    Question 28
    A network engineer wants to ensure an optimal end-to-end delay bandwidth product. The delay is
    less than 64 KB. Which TCP feature ensures steady state throughput?
    A. Window scaling
    B. Network buffers
    C. Round-trip timers
    D. TCP acknowledgments
    Answer:A
    Also that wrong the right answer is B
    For the dumps, you can send me at ahmedrofaii at gmail dot com , I will be glad to send them to you freely , for routing dumps and for switching , tshoot dumps
    I wish for you good luck in your exam 

  23. ahemd erlrofaie
    January 24th, 2017

    i forget to mention that there was also in my exam
    -the policy based routing sim

  24. Hiko
    January 25th, 2017

    Thank you ahemd for sharing exam practice

  25. JIES
    January 26th, 2017

    I took the exam on January the 23rd and 149, 41 are still valid

  26. ahemd erlrofaie
    February 1st, 2017

    here i sent in link below all the dumps for the three exams
    regrading the switching exam you can depend on 191q dump
    regarding to routing exam, you will find the 149q + 41q dump , also you will find the 183q\32q\8q dump you have to study them all
    regrading to tshoot exam you will find pass4sure dump , beside the dump you have to depend on networktut site for the tshoot

    https://drive.google.com/drive/folders/0B21TuNHP-x2dc2U5MUlNOXFkd2c?usp=sharing
    ​good luck????????

  27. Shan
    February 2nd, 2017

    Hello Guys
    If any one need CCIE r/s lab version 5.0 dumb please mail me. but not free.
    nkssujith @ yahoo.com

  28. Martin
    February 5th, 2017

    ahemd erlrofaie thank you so much

  29. Anonymous
    February 8th, 2017

    Thanks for those corrections ahemd. I agree they are wrong.

  30. Digital
    February 11th, 2017

    Guys,

    Good to read from here and thanks Ahemd for those corrections – I plan to take my 300-101 next week, is 41 Tagwa dump still valid

  31. Mandark
    February 11th, 2017

    Hi All,
    Passed my ROUTE about 2 hours ago with a score of 8xx. Used only 149q and TAGWA. Simulations: eigrp/ospf redistribution,
    Ospf sim, ospf (ipv6), PBR, OSPF Evaluation. Thanks to digital tut

  32. Digital
    February 11th, 2017

    Congratulations Mandark and thanks for the updates. Still studding for mine, I am scheduled to take it next week. I need some help on the sim, I like to ask you some questions, can you reach me at {email not allowed} ??

    Thanks.

  33. Anonymous
    February 12th, 2017

    Gents,

    Regarding this 149q + 41q dump,

    somebody can give me to this 41q dump? i have only 149q

    {email not allowed}

  34. Mjereza
    February 12th, 2017

    hi guys please help with latest dumps CCNP 300-101…. email:

    j.malapane at yahoo dot com

  35. a kind
    February 12th, 2017

    Hi, I know actually there are new questions, I fail my exam because there are a lot of new question, can somebody help me with the new questions??

    thanks a lot

  36. Anonymous
    February 13th, 2017

    a kind, what sort of questions did you get? Can you recall any????

  37. a kind
    February 13th, 2017

    For example for the Ospe Evaluation the timers between R3 & R2 and R3 & R1, when you use the command for check the timers, there’s no one answer to correspond with the true timers, questions about ip sla, questions about phases of autentications, I know in some blugs I was reading that they added new questions, does some one have the new pool (New Questions) and how many new questions are?

  38. sam
    February 13th, 2017

    Please share the new questions for ccnp 300-101

  39. Nivi
    February 14th, 2017

    Guys i wrote 300-101 today and passed 816..but many questions were new..i did study 149q+41q+15q+32q+8q+182q and went, but still got around 13 new questions…please make sure u study new ones also….sorry i don’t remember the new questions, otherwise i would have posted here…

  40. quales
    February 14th, 2017

    i think cisco is running interactive tests at this point sounds like it to me with all these peeps saying we got newer questions years ago the thing wouldnt change in 3-4 years;again I think its from unskilled canidates actually making it thru an interview and cannot do the work reqiured hence getting the hiring manager in trouble now manager sees certs as an ass wipe when no tp is available. Another thing they can do is make the interview more technical mine have never been hard OSI,ports numbers? really. They should set u down in a room and give u tasks to do in gns3 that reflect what an NP should know. done u either do the task or not dont know why they dont employ this exercise it would get rid of all the real cheaters that troll this site.

  41. Borge
    February 14th, 2017

    redistribute ospf 1 metric 10000 100 255 1 1500
    question test takers has anybody had the ballz to just use:
    redistribute ospf 1 metric 1 1 1 1 1
    easier and it will work

  42. Tivo
    February 15th, 2017

    Passed today. 819. Reviewed 149q+41q. Lots of questions that weren’t in those. Perhaps there in the 183 dump. 1 new question for every 3 that I recognized. More than 10 that werent in those 2 files. Simulations same.

  43. zambia
    February 15th, 2017

    ahemd erlrofaie

    Thanks for your share…..

  44. Mpolvora
    February 19th, 2017

    good evening,

    Do I get the delivery of the 149q + 41q?

    Thanks

    {email not allowed}

  45. Mpolvora
    February 19th, 2017

    good evening,
    Do I get the delivery of the 149q + 41q?

    mpolvora at gmail dot com

    Thanks

  46. Mpolvora
    February 19th, 2017

    good evening,
    Do I get the delivery of the 149q + 41q?
    mpolvoratjp at gmail dot com
    Thanks

  47. Mohammed
    February 21st, 2017

    redistribute eigrp 100 metric-type 1 subnets
    guyz 1 silly doubt in above command metric-type 1 << is this 1 is ospf process number??

  48. Hiko
    February 22nd, 2017

    Mohammed, it defines OSPF External type. you can set 1 and 2.
    http://blog.ine.com/2011/04/04/understanding-ospf-external-route-path-selection/

  49. Anonymous
    February 23rd, 2017

    passed yesterday, got 10/12 new questions never seen in dumps (about timed access list, easy vpn, ssh block access, frame relay, ipv6); labs and simlet all from known dumps (redistribution, pbr, ospf virtual link, eigrp stub); a total of 49 items to me, most from dumps. Minimum to pass 790, scored 947.

  50. Hiko
    February 23rd, 2017

    Which dumps did you use? Please write name of dumps

  51. Anonymous
    February 23rd, 2017

    i have renamed them all, anyway they are something like: ccn route labs from digitaltut, tagwa 41q, pass4sure 141q, passleader 183q + some updates, actualtests 149q, examcollection 149q, digitaltut apr-2016, waleed 15q

  52. Tonka
    February 23rd, 2017

    @Anonymous, congrats on your awesome score.

    Please confirm, you had eigrp stub lab (http://solidcon.ph/?viewid=route-eigrp-stub-sim)?
    Others have recently reported OSPF Sim (http://solidcon.ph/?viewid=route-ospf-sim); but you did not get this one?

    What simlet(s)? Many are reporting OSPF Evaluation Sim.
    Any drag & drops?

    Sorry for so many question; I take my exam very soon and am getting nervous.

    Any additional insight you can provide is greatly appreciated.

    Thanks in advance.

  53. GG
    February 23rd, 2017

    Redistribution sim: when looking for the load , which value do you use? txload or rxload both?

  54. GG
    February 23rd, 2017

    Redistribution sim when looking for load on the interface, which value do you use? do you use or the other or add both rx and tx and divide by 510?

  55. JennYC
    February 25th, 2017

    Hi guys, I just want to ask FOR THOSE WHO ALREADY TOOK THE EXAM

    does it really show a wrong OSPF process of 1? and you cannot change it? (like what we have downloaded)

    or you need to create a OSPF process of 23 and 24?
    Thanks guys and also how do you get the load when theres TX and RX load?

  56. JennYC
    February 25th, 2017

    Sorry guys dont mind the questions. I thought it was process ID but areas 23 and 24 XD

  57. Avi
    February 28th, 2017

    Do we add router ospf 1 or router ospf 24?
    please help am confuse

  58. DAP
    February 28th, 2017

    arrgg exam soon and getting more confused .

    redistribute eigrp 100 metric-type 1 subnets

    Is the 100 part of the above the eigrp process id which can be found in show run ?

  59. CCIE
    March 5th, 2017

    Yes, thats the EIGRP AS number (process ID is OSPF).

    So you are telling it to redistribute EIGRP 100 into OSPF 1.

    Remember to use the subnets command.

  60. scarlow
    March 5th, 2017

    I’m writing today and i doubt if I’m ready. I’m confident about all simulations but drag and drops are kicking my behind.

    Can anyone who recently wrote tell me which drag and drops should I expect??

  61. non-name
    March 7th, 2017

    Dear all,

    ı failed 300-101 exam( 75x/1000).ı studied 149+41(takwa)+183.
    there are new about 10 f*king questins.
    All digitaltut lab is available.
    take care about exam.

  62. non-name
    March 7th, 2017

    failed

  63. non-name
    March 7th, 2017

    Dears,
    I failed today 7xx/1000.I studied 149+41(takwa)+183+Labs.But in my exam there was about 10-15 new f*king questions.
    All digitaltut lab are available.
    regards.

  64. Anonymous
    March 7th, 2017

    @non-name, you forgot Waleed’s 15q file. You will find his link through previous pages of the “share your ROUTE v2.0 experience” page…

  65. alim2017
    March 10th, 2017

    hello guys ,can someone send me the valid dumps for 300-101
    i’m writting my exam within four days.

    tsafongromuald at gmail dot com

    regards

  66. Anonymous
    March 10th, 2017

    can some one plz tell me what are the SIMULATION in route exam …plz help me iam writing in a couple of days

  67. JIG
    March 13th, 2017

    Hi, can someone explain why in the 1st CASE “metric-type 1” is used in the redistribute command on R3. That makes traffic to choose not shortest path (Ethernet Area 34) when coming back from R4 to R1.
    I think it should be just “redistribute eigrp 100 subnet” because when traffic going back would choose Serial area 24 because it would prefer E1 route over E2.
    Right?

  68. JOJO not so smart guy
    March 20th, 2017

    PLEASE READ********

    Hi Guys. Please send me latest dumps. I badly need it. please have mercy.
    Send me here:
    ciscoreview2017(@)(yahoo)(dot)(com)

    Thank you so much guys
    :( I’ll Appreciate

  69. Anonymous
    March 21st, 2017

    I had the lab with Fastethernet link, but I was not able to use distance command “distance eigrp 90 105”.
    When tried using question mark “distance eigrp 90 ?” it showed no avaiable options or description. I submitted the full command, it was visible in running config but no change in ip routing table happened. Traceroute was still the same via serial link. Finally I removed the command and go to next question.
    Most quesions are still valid. Maybe had some new ones. CHAP drag&drop .
    Pased with 790 points .

    @BEST EFFORT
    dont know if your still posting on this site, but that is exactly what happened to me. I figured out our problem we did not divide the delay by 10 its also why our distance command did not work, but the funny part is I got a 790 as well! I think if u have at least the configs in the sim, but it wont ping cisco gives u partial credit. But, I think in our situation the score just defaulted to 790 which sux, I know, I am still upset about it. It defaulted to 790 because cisco was not going to give us overall credit like I think these sims are worth 100 points so we should have got 890/900ish because 1000-100=900 . Now they were not going to be that nice and just defaulted the score 790 they know peeps study their asses off for this thing as I saw this as a pity (studied for an A and got a C) score.

  70. DAP
    March 21st, 2017

    to put the distance eigrp 90 105 command

    do you need to go into eigrp process id first ?

    Eg
    #conf t
    #router eigrp 100
    #distance eigrp 90 105

    or is it just in configuration mode ?

    Hope that makes sense

  71. Anonymous
    March 21st, 2017

    #conf t
    #router eigrp 100
    #distance eigrp 90 105

    did that , it was not the problem if u read please stay abreast

  72. DAP
    March 22nd, 2017

    I was wondering as starting to doubt what i did the last time i attempted the exam

  73. san 2017
    March 23rd, 2017

    Hi Everyone,

    Please share this dumps 149q+41q+15q or any latest valid dumps if available.

    san242721 @ gmail com

  74. Laksh
    March 26th, 2017

    Hi All,

    I give my exam on 23rd of this month. On sims after implementing the configuration, copy running start-up command is not worked for 2 sims. I claimed same with exam instructor. But He is trying to call pearson guy to check but my exam time was on going. It was nightmare. Finally my time got over. I got 690 marks. My two sims EIGRP OSPF Redistribute and OSPF sim worked fine. but unable to save it. My two SIMS almost 200 marks lost there itself with their mistake. I suppose to get 890 marks. Could you please tell anyone how to claim if there’s mistake ? and also confirm what is the marks for each sim ??

  75. waheed ullah
    March 29th, 2017

    hello everyone

    please can anyone send me CCNP route update dump.

    here is my email
    {email not allowed}
    i need the update dumps so much
    thanks

  76. waheed ullah
    March 29th, 2017

    w a h e e d f a c e b o o k @ g m a i l . c om

  77. Kash
    March 31st, 2017

    Hi ,, i have my exam in two weeks time , can anyone send me valid dumps, the 149+41+15 questions.. email priscakash@(gmail).(com)

  78. Anonymous
    April 3rd, 2017

    I passed the 300-101 exam today with an 895. 149+41+15 is still valid. There were new questions in there but not enough to fail you if you know everything in these three dumps. I got a couple of BGP questions that were not in here.

    All labs are still valid.

    Good luck.

  79. Dumps
    April 4th, 2017

    DOWNLOAD VCE and PDF here *only 15 bucks
    149+41+15 is 100% good in exams

    http://rebrand.ly/ccnpr370d

  80. DAP
    April 5th, 2017

    Thanks for response

  81. Syed
    April 9th, 2017

    There are some new questions as well in the exam, almost 10 new question, with some new drap and drop… Does anyone have that

  82. DAP
    April 12th, 2017

    So once you have completed this in the exam you do show ip route on R1 to see the 172.16.100.1 network (the network behind R4) in the routing table of R1 and make a ping from R1 to this network.

    what about telnet or trace route to test further ?

  83. MAGIC
    April 13th, 2017

    PLZ SEND ME DUMPS AT {email not allowed}

  84. salll
    April 13th, 2017

    plz fox send me valid dumps at( murwan.ahmed95 @ gmail com)

    am palnning to take the exam next week ……
    thanks guyz
    regards

  85. Gosh
    April 14th, 2017

    Just failed the exam even nailing all labs they are pretty easy. Questions are all new just a few questions that are mentionend here. i failed with 710 out of 790.

  86. TheOnlyPrincess
    April 14th, 2017

    @Gosh – those new questions are totally new? have you seen the new 18q from page 160 in the shared section?

  87. kia Mal
    April 15th, 2017

    {email not allowed}

  88. Arshad
    April 17th, 2017

    @Gosh
    can u please tell me about the labs which one you got and r they the same or thiere were changes please help my iam writing my exams in 2 days

  89. Anonymous
    April 18th, 2017

    Hi TheOnlyPrincess,

    Took the exam today and failed 770. Share me your 160 dumps and I will check if new questions are

  90. gooduser
    April 19th, 2017

    Please forward up dated dump to this email usmaco @ yahoo dot com

    Thank you in Advance

  91. awe
    April 20th, 2017

    please please share updated dumps to this email nzimande.worldwide @ gmail.com thank you in advance.

  92. DAN
    April 25th, 2017

    Hi all gigs
    is the below are the labs that is in the exam ????????????????????/

    eigrp ospf redistribution
    ipv6 ospf virtual link
    ospf
    ospf evaluation
    PBR

  93. Josep
    May 2nd, 2017

    Hi everybody!

    I’ve just noticed that doing this lab like it’s explained in the solution we have ASYMMETRIC routing!! is this expected?

    The way from R1 to R4 will be R1 -> R2 -> R4, that’s OK.

    But the way back from R4 to R1 will be R4 -> R3 -> R2 -> R1

    And that’s because when we configure redistribution of EIGRP to OSPF on both R2 and R3, we see that metric is better in the redistribution of R3 since the link R3-R4 is FastEthernet and has better bandwith and delay than the link betwen R2-R4. So R4 chooses R3 in the way back to 192.168.1.0 as we can see in the routing table:

    R4#sh ip route

    Gateway of last resort is not set

    172.16.0.0/24 is subnetted, 1 subnets
    C 172.16.100.0 is directly connected, Loopback0
    C 192.168.4.0/24 is directly connected, FastEthernet0/0
    O E1 192.168.1.0/24 [110/30] via 192.168.4.2, 00:02:35, FastEthernet0/0 <—
    O E1 192.168.2.0/24 [110/30] via 192.168.4.2, 00:02:35, FastEthernet0/0
    C 192.168.3.0/24 is directly connected, Serial0/0
    R4#

    Does anybody else noticed that? what do you think? is correct?

    Thanks in advance! :)

  94. Red
    May 5th, 2017

    Plz send dump to red.digitaltut @ gmail . com

  95. momo
    May 11th, 2017

    Hi Guys. I prepare the ccnp exam. Please send me latest dumps. I badly need it.
    Send me here:
    nathaliemomo95(@)(yahoo)(dot)(fr)
    Thank you so much guys

  96. Anonymous
    May 15th, 2017

    hi…plz tell which dumps r valid

  97. Anonymous
    May 15th, 2017

    any person who gave exam today…plz update here..

  98. Anonymous
    May 17th, 2017

    hi Guys,

    I gonna pass mine this Friday , can some one share with me the new dump here : {email not allowed};

  99. Anonymous
    May 17th, 2017

    {email not allowed}

  100. Anon
    May 18th, 2017

    I still don’t see the point in “distance eigrp 90 105”.

    Why is going R1 -> R2 -> R3 -> R4 better than going R1 -> R2 -> R4.

    R1 -> R2 -> R3 -> R4 = 2 x Serial + 1 Ethernet.
    R1 -> R2 -> R4 = 2 Serial.

Comment pages
1 2 26
  1. No trackbacks yet.